BCM® PNT Trigger Assembly AR15

MSRP: $70.00
Your Price: $65.95
(You save $4.05 )
(184 reviews)
SKU:
BCM-PNT-TA1
BCM® PNT Trigger Assembly AR15
Stock Status:

 

BCM® PNT™ Trigger Assembly (Polished - Nickel - Teflon)

BCM quality, modern manufacturing processes, and aerospace coatings are combined to ensure parts last a lifetime while performing far beyond requirements established nearly six decades ago.

The BCM PNT Trigger and PNT Hammer are a precision machined Mil-Spec AISI8620 investment casting per the USGI TDP (Mil-Spec) for M16/M4 family of weapons. (not to be confused with MIM parts that are very common in the commercial market). 156/157 holes are honed to assist in perfect alignment and a smooth trigger pull.

After that, the BCM PNT Trigger and PNT Hammer then goes through a 3 step heat treat and case hardening process for optimal grain structure alignment, yielding a stronger and more wear resistance product.

 

Polished

The sear engagement surfaces are ground, but then hand polished for an increased smoothness and reduction in friction up to 300% beyond the Mil-Spec.

 

Nickel

An electroless nickel finish is applied for a smoother trigger pull with less "grit" and reduced felt "creep". Nickel also provides a long lasting finish that will not corrode, rust, or discolor due to oxidation.

 

Teflon

Teflon particles are embedded in the nickel, further reducing the friction of the interface and ensuring a long lasting coating. This is done on both the BCM PNT Trigger and Hammer in order to provide the maximum benefit allowed by the nickel coating, by augmenting the low friction and corrosion resistance.

 

This assembly includes our impact resistant trigger and hammer pins. They are centerless ground to a fine finish and superior tolerances to ensure compatibility with all MIL SPEC lower receivers built per the USGI TDP.

The BCM Disconnector is stamped from a 1070 material and fine blanked for cleaner edges, double disc ground to precise size. All hammer engagement surfaces are also ground for a super clean reset.

 

The processes and tolerances are matched in the BCM PNT Trigger Assembly to create a system better than the sum of its parts.


As with all BCM products, Made in the USA.



***This product contains chemicals/materials known to the State of California to cause cancer and other reproductive harm. To learn more, visit www.p65warnings.ca.gov.***

184 Reviews

  • 5
    Awesome

    I am very happy with my oder it was very easy to do online shipping was great the package was packed very good over all A+++++++++ all the way I tell any as much as I can about getting all there stuff from Bravo all the time thank you and I will be ordering again from here for sure

  • 5
    PNT Trigger

    Awesome trigger very smooth still a little stiff tested around 6.5 but a huge improvement from the mil spec trigger

  • 5
    Customer review

    Shipping time was awesome! Trigger assembly was way more than I expected...fit was perfect, the break was excellent. I'll be back.

  • 5
    Good Trigger

    Very smooth. You know when it's going to fire.

  • 5
    Great Trigger

    I purchased the BCM PNT Trigger to replace a cheap trigger I had previously in my AR that stopped functioning properly. The BCM trigger works great and exactly as intended.

  • 5
    excellent product

    This trigger is amazing! It exceeded all my expectations. Thanks for a great product and excellent customer service BCM.

  • 5
    Great Product

    This trigger is smooth as butter, I love it

  • 5
    Quick shipping. Perfect addition.

    Perfect addition as I’m stocking up on parts for my next build. For the price, it’s hard to find another Mil-Spec trigger of this quality and function.

  • 5
    BCM Products

    The BCM pnt is a great milspec trigger. I use to run Geisselle and Larue but I started favoring a slightly heavier trigger, just out of personal preference, and the PNT fits the bill. Coating makes it a smooth trigger. Crisp break. Loud reset.