BCMGUNFIGHTER™ AR-15 Enhanced Lower Parts Kit - Wolf Gray

MSRP: $130.00
Your Price: $119.95
(You save $10.05 )
(44 reviews) Write a Review
SKU:
BCM-ELPK-WG
Stock Status:

Out of stock

BCM® Enhanced Lower Parts Kit for your AR15 Lower Receiver

This kit includes all the Mil-Spec quality components you have come to expect from BCM, along with some fantastic upgrades to include;
BCM PNT Trigger Assembly
BCM Pistol Grip, Mod 3
BCM Enhanced Trigger Guard

In a commercial market flooded with imported and low quality Mil-Spec imitations, you can trust that BCM parts are made in the USA and to the highest standards. Please look at the information below.


BCM PNT Trigger Assembly (Polished Nickel Teflon)

BCM quality, modern manufacturing processes, and aerospace coatings are combined to ensure parts last a lifetime while performing far beyond requirements established nearly six decades ago.

The BCM PNT Trigger and PNT Hammer are a precision machined Mil-Spec AISI8620 investment casting per the USGI TDP (Mil-Spec) for M16/M4 family of weapons. (not to be confused with MIM parts that are very common in the commercial market). 156/157 holes are honed to assist in perfect alignment and a smooth trigger pull.

After that, the BCM PNT Trigger and PNT Hammer then goes through a 3 step heat treat and case hardening process for optimal grain structure alignment, yielding a stronger and more wear resistance product..


Polished
The sear engagement surfaces are ground, but then hand polished for an increased smoothness up to 300% beyond the Mil-Spec.


Nickel
An electroless nickel finish is applied for a smoother trigger pull with less grit and reduced felt creep . Nickel also provides a long lasting finish that will not corrode, rust, or discolor due to oxidation.


Teflon
Teflon particles are embedded in the nickel, further reducing the friction of the interface and ensuring a long lasting coating. This is done on both the BCM PNT Trigger and Hammer in order to provide the maximum benefit allowed by the nickel coating, by augmenting the low friction and corrosion resistance.

This assembly includes our impact resistant trigger and hammer pins. They are centerless ground to a fine finish and superior tolerances to ensure compatibility with all MIL SPEC lower receivers built per the USGI TDP.

The BCM Disconnector is stamped from a 1070 material and fine blanked for cleaner edges, double disc ground to precise size. All hammer engagement surfaces are also ground for a super clean reset.

The processes and tolerances are matched in the BCM PNT Trigger Assembly to create a system better than the sum of its parts.


Bolt Catch and Safety Selector

The BCM Bolt Catch and Safety Selector are a Mil-Spec AISI8620 investment casting per the USGI TDP for M16/M4 family of weapons. (not to be confused with MIM parts that are very common in the commercial market)

The Safety Selector is center-less ground. The Selector and Bolt Catch are machined to the Mil-Spec , then goes through a 3 step heat treat and case hardening process for optimal grain structure and wear resistance. Has a phosphate finish for corrosion resistance.


BCM Magazine Catch

The BCM Magazine Catch Assembly (plate and the post) is precision machined Mil-Spec AISI8620 per the USGI TDP for M16/M4 family of weapons. (not to be confused with MIM parts that are very common in the commercial market) and a hardened alloy steel shaft.

The BCM Magazine Catch is machined to the Mil-Spec , then goes through a 3 step heat treat and case hardening process for optimal grain structure and wear resistance. The shaft is hardened, centerless ground, and precision threaded. Parts are assembled and staked per the USGI TDP and given a phosphate finish for corrosion resistance.


BCM Rear Takedown Pin and Front Pivot Pin

BCM Rear Takedown Pins and Front Pivot Pins are made from AISI8620 bar stock and machined per the USGI TDP for M16/M4 family of weapons. Our takedown pins are given a 3 step heat treat processes and the diameters are ground to final size prior to a corrosion resistant phosphate finish.


BCM Detents and Springs

Takedown detents include a cadmium chromate coating to resist corrosion and prevent them seizing in the small holes of the lower receiver while the Buffer retainer and Bolt Stop Plunger are made from hardened alloy steel for wear resistance and finished with a phosphate coating to prevent corrosion. The Springs are 17-7PH Stainless Steel to prevent corrosion and retain adequate tension for a lifetime of service.


This BCM Enhanced Lower Parts Kit includes:

1. BCM PNT Hammer
2. Hammer Spring
3. BCM PNT Trigger
4. Trigger Spring
5. Hammer/Trigger Pins
6. Disconnector
7. Disconnector Spring
8. Bolt Catch
9. Bolt Catch Plunger
10. Bolt Catch Spring
11. Bolt Stop Pin
12. Rear Pivot Pin
13. Buffer Retainer
14. Buffer Retainer Spring
15. Magazine Catch Button
16. Magazine Catch Spring
17. Magazine Catch
18. Rear Take Down Pin
19. Selector (Safety)
20. Selector Detent
21. Selector Detent Spring
22. BCM Enhanced Trigger Guard
23. BCM Trigger Guard Pin
24. BCM Trigger Guard Screw
25. BCM Pistol Grip Mod 3, Grip Screw, Locking Washer
26. Take Down/ Pivot Pin Detent
27. Take Down/ Pivot Pin Detent Spring


As with all BCM Professional Grade Weaponry , Made in the USA.

***This product contains chemicals/materials known to the State of California to cause cancer and other reproductive harm. To learn more, visit www.p65warnings.ca.gov.***

44 Reviews

  • 5
    Lower parts kit

    Posted by Dennis Page, JR on Apr 30th 2020

    Very impressed with shipping and packaging by Bravo, especially when everyone is using this China virus as an excuse to slow things down. Bravo was on top of things as they always are! No BS excuses, just results! Product is great, just what you would expect from a top tier producer like Bravo. You won’t be disappointed with this kit, spend the extra money and buy the Bravo kit. I love the grip, one of the best I’ve ever used.

  • 5
    Lower parts kit

    Posted by James on Apr 27th 2020

    I have found the best kit.

  • 5
    Amazing

    Posted by Brady O'Dell on Apr 25th 2020

    Fast shipping and super easy build love the feeling of components

  • 5
    Best of the best

    Posted by Dangerous Hunk on Apr 23rd 2020

    I have used several lower parts kits over the years on different builds. This is by far the best. Proper sized takedown pins, very smooth and creep free trigger. The pistol grip angle is perfect for SBR or braces pistols. Overall I am extremely pleased with the finished product.

  • 5
    Enhanced AR lower parts kit

    Posted by al on Oct 11th 2019

    I bought my second lower parts kit with confidence after installing my first BCM lower kit knowing if they put their name on it the quality is priority one.
    Fastest delivery is a bonus
    Thank you BRAVO CO.

  • 5
    Wolf Gray products

    Posted by Nicholas McLaughlin on Oct 8th 2019

    Bravo company is top of the line just put my rifle together still needing a couple more pieces but loving it so far Your company is top of the list as far as AR-15’s are concerned and l’m really enjoying it however I ordered ar15 grips and a buttstock and I got the wolf gray rail covers but I’m really hoping for a wolf gray angled fore grip and wolf gray magpul buttstock slash flip sights I ordered gray flip sights and an angled fore-grip from magpul itself and although their company is also awesome, the color does not match at all it’s a dark gray while as BCM’s is a light gray I’m going to give you guys 5 stars because I like the quality but as a loyal customer I expect more wolf gray options and soon! I really wanted to build a foliage green AR but you guys are constantly out of stock on things I need and if you guys could only keep up with the supply side the demand and quality are in place to make a profit. you could really maximize profits by having more color options available

  • 5
    Customer review

    Posted by David Woodson on Sep 14th 2019

    Review body is empty

  • 5
    Lower Parts Kit

    Posted by Brandon Anglesey on Aug 20th 2019

    Love this product works great. Good clean crisp trigger.

  • 5
    Exactly what I wanted.

    Posted by Jaycen Rigger on Jul 17th 2019

    I love the Wolf Gray. I wish more of the BCM items were available cerakoted in the same color.

    The pistol grip is ergonomically superior on my AR pistol. And the polished Nickle Teflon trigger is smooth with a crisp break. Pins, buttons and springs are mil-spec and just fine.